For contact info, please see the Sci.Electronics.Repair FAQ Email Links Page.
Copyright ©; 1997-2006
Reproduction of this document in whole or in part is permitted if both of the
following conditions are satisfied:
1. This notice is included in its entirety at the beginning.
We will not be responsible for damage to equipment, your ego, county wide
power outages, spontaneously generated mini (or larger) black holes, planetary
disruptions, or personal injury or worse that may result from the use of this
material.
These all use optical technology very similar to that of the compact disc
and CDROM. Thus, most problems with these cousins of the CD will be similar.
See the document: "Notes on the Troubleshooting and Repair of Compact Disc
Players and CDROM Drives" for an introduction to the basic technology, general
maintenance procedures, and diagnosis of most common problems. This document
addresses those aspects of the technology and repair that are unique to each
of these other formats. Problems with Sony PlayStation PSX (and similar)
CDROM-like game machines are covered there as well.
Once CD (and DVD) rewritable technology becomes more popular (and lower in
price), these will be added. I currenty have little information on this
equipment.
Contributions are always welcome as you will note that there really isn't that
much specific information at the present time on anything other than LaserDisk
players and even this is sparse. I don't expect that much interest in or
offers of CD-R, WORM, or MO repair information. However, MiniDisc has some
sort of a following and we are destined to be inundated with DVD problems in
the near future as they replace CDs as the equipment of choice. I am still
waiting to see the inside of a DVD player - working or otherwise :-).
This isn't that much of a problem with LaserDisk players since the laser power
is likely (but not guaranteed!) to be similar to that of a CD player where
relatively minimal precautions are adequate.
However, for the technologies which can record or write on an optical disk,
the laser power may be much higher and instant irreversible damage to vision
is quite possible. Furthermore, these are almost always IR (infra-red) lasers
which are for all intents and purposes, invisible. Proper precautions are
essential and laser-blocking goggles are definitely recommended whenever
the unit is powered without a laser shield in place. Once you damage both of
your original equipment eyesballs, you don't receive any replacements (even if
they are still under warranty - read the fine print of your contract)!
General safety precautions:
While there are fewer potential dangers involved in servicing an LD player or
MO drive compared to a TV, monitor, or microwave oven, precautions are still
required when working with the cover removed. These relate to electrical
connections to the AC line, getting caught in the mechanisms, and exposure to
the laser beam:
Some equipment such as LaserDisc players may use switching power supplies
with their own set of problems. Internal drives may include their own DC-DC
converters as well (which are not particularly dangerous but can be easily
damaged through the careless slip of a probe). In these case, see the
document: "Notes on the Troubleshooting and Repair of Switchmode Power
Supplies" for more information.
Where an older LaserDisc player uses a Helium-Neon (HeNe) laser, there will
be a high voltage power supply for the HeNe laser tube. While this is
probably not powerful enough to kill you, a reflex action from touching the
wrong terminal can result in collateral damage like ripped flesh from sharp
sheet metal parts. These terminals are usually clearly marked and insulated
but make a note of their location to be safe and add several layers of
plastic electrical tape if they are exposed.
ALL THE HIGHER POWER LASERS ARE LIKELY TO BE IR AND INVISIBLE! You won't
be able to see a bright beam you can avoid! The laser in all these devices
is infra red, near IR - around 780 nm - border of visible range but for all
intents and purposes invisible. While the laser is supposed to be set to
low power for playing or reading POWER CIRCUITS CAN FAIL! Don't take any
chances. At most, you will see a tiny red dot in the lens as shown in
Appearance of IR (780 nm) Laser in CD Pickup.
(Original photos courtesy of Gag Helfront (ie.dunster@ukonline.co.u).)
With a visible beam, it is easier to avoid exposure and LD and DVD players
use low power lasers anyhow. Reflections at these power levels are not
strong enough to be a serious hazard. This will change eventually as DVD
recorders and writers using higher power visible lasers are introduced.
As a comparison, these will likely be similar in power level (5 mW) to the
brightest laser pointers currently on the market and are a definite risk to
vision at close range. Still, being visible, it is easy to avoid direct
exposure.
However, for an IR laser producing an invisible beam, there is no way to
reliably avoid the beam visually. With the optics intact (no damage to the
pickup and none of the covers on the pickup removed) and a disk in place on
the spindle or the lens covered with black tape (no holes!), it should be
safe to work at a reasonable distance. Don't put one of your eyeballs up to
the optical block - there could always be a light leak! Proper IR blocking
goggles would definitely be a good idea where exposure to these higher power
lasers is possible.
CAUTION: There is usually a very low intensity (in appearance) emission
from an IR laser which appears deep red. It will be visible as a spot the
size of the period at the end of this sentence when the lens is viewed from
an oblique angle. This is just your eye's response to the near IR energy of
the main beam. (Some people apparently cannot see this at all.) Do not be
mislead into thinking that the laser is weak as a result of how dim this is.
The main beam is up to 10,000 times more intense than it appears! It's
power output is generally around 1 mW - comparable to a laser pointer. Take
care. However, the red dot is an indication that the laser is being powered
and probably functional, though it is no guarantee of the later. You really
need a laser power meter or at least an IR detector to confirm the existence
of an IR laser beam.
Also check out:
The following sites have a variety of information on CD and DVD technology:
A couple of sites with CD-R specific information including some repair tips is:
In terms of performance, video quality from the Laserdisc medium can be far
superior to even SVHS and SuperBeta when viewed on a correspondingly high
quality TV/monitor. Like a CD and unlike tape, access to any scene or even
frame is nearly instantaneous. This is definitely a significant advantage for
the casual viewer. However, it is the enabling technology for interactive
learning and games. With over 65,000 individual frames on a side, this is
a potentially very powerful way to present information as combinations of
stills and moving segments and permit context dependent control of access
or video action.
High-end video enthusiasts swear by Laserdisc technology but this medium
never caught on due to its relatively high cost of both the equipment and
the software (movies), limited rental availability, and because it is a
play-only media. In addition, the capacity (NTSC) of a single LaserDisc is
around 1 hour total on both sides requiring frequent disc changes even if the
player has dual laser pickups.
The basic eletro-optical mechanism is similar to that of a CD including the
techniques used for beam generation, focusing, and tracking. However:
The original version is covered in The "Television Engineering Handbook"
edited by Benson from McGraw-Hill, 1986. Don't know about the newer version
with digital sound. (Or what the newer edition of the book covers, either).
It's an analog FM system at 8 MHz that records the composite signal, with two
FM audio carriers at 2.3 and 2.8 MHz.
It is NOT related to LaserDisc technology and does not use an optical pickup.
If you found one of these, you have a classic dinosaur! The CED system was
something RCA spent $200-300 million to develop about the same time that
LaserDisc technology was being perfected. Guess which won!
And, this was shortly after the same company spent a similar vast amount of
money on another consumer electronics dud. It was also named Selectavision if
I recall correctly and used optical scanning of 4 mm (??) movie film.
CED uses a capacitive contact sensor 'sled' running in a grooved disc.
The pickup actually rides on the disc like the stylus on a phonograph record.
The sensor detects minute changes in the capacitance between the tip of the
pickup and the metallized surface of the disc embossed with millions of tiny
bumps and valleys.
This really isn't that bad - the system DID work but suffered from some of the
same problems as records - wear, critical tracking requirements, etc.
If you are trying to resurrect a CED player, you better have the discs you
want because they will not be available at your neighborhood video store!
Since it is more than 15 years old, there can be any number of problems with
the equipment just from age and non-use. These are likely to be both
mechanical (gummed up grease, dirt), and electronic (dried up electrolytic
capacitors in the power supply, bad connections, etc.).
However, chances are good that it wasn't actually broken to begin with since
consumers likely gave up on this technology before it actually failed - there
just wasn't enough movies/programming available.
Start by checking the obvious, reseating all connectors, testing power supply
voltages and for ripple, etc.
It certainly would be cool to get working.
MDs may be pressed like CDs with the information encoded in pits and lands.
This is the way prerecorded play-only MiniDiscs are made.
For recording, the MiniDisc technology uses a higher power laser beam (upped
to 5 mW at the disc surface) to heat a magneto-optically active coating to
above its cure point (where magnetization is lost). A writing coil in close
proximity to the back of the Minidisc is used to switch the magnetic field
polarity (N or S) of the coating as it cools. Thus, the laser beam may be
thought of as 'softening up' the magnetic material but the actual writing is
by the coil. This is not the same way most other writable magneto optical
drives are implemented. See the sections: "WORM drives" and "Magneto optical
drives" for more details on these other media.
For playback of this magneto-optical (MO) recording, the pickup uses what is
known as the 'magneto-optic Kerr effect'. When a polarized laser beam is
reflected from the disc coating, its polarization orientation is rotated
slightly depending on the magnetic field polarity (N or S). This rotation
is small (about 1%) but enough to permit detection. However, since it is
so small, it isn't surprising that there can be problems with the optics and
front-end electronics for MO readback.
Thus, the MiniDisc pickup and front-end operates in three modes: spatial (pits
and lands) read, MO read, and MO write.
The basic mechanism and optical pickup is similar to that of a CD including
the techniques used for beam generation, focusing, and tracking. However:
The basic components are very similar and thus cost of manufacture will be
similar. So, why produce old fashioned equipment?
The DVD permits storage of up to 4.5 GB per information layer with up to 2 of
these on each side (one under the other) for a total of 18 GB if fully
implemented. This means (per layer):
From a marketing perspective, it is essential for DVD equipment to support
the CD format. However, since DVDs and CDs differ in terms of feature size,
track spacing, thickness, and so forth, it would not be very effective to
simply shine the DVD pickup at a CD! Either of two approaches may be taken:
Some people seem to think blue lasers are used for DVDs. One reason may be
that manufacturers are putting blue illumination on the front panels and maybe
even inside the disc compartment of DVD players - solely for marketing reasons.
However, blue or UV lasers (e.g., argon or krypton ion) may be used to write
the glass master for DVD (as well as CDs) where the shorter wavelength results
in crisper more accurate rendition of the pits and lands of the information
layer. Of course, these machines cost $250,000.
Converting to a shorter wavelength laser for readout won't help anything
except the manufacturer's bottom line assuming they could charge much more
for the hype than the additional cost of the laser. Currently, the only
viable option is the Nichia 400 nm violet laser diode which go for about $2K
each! To take advantage of a shorter wavelength laser, the entire standard
would need to be revamped. I have already named the new standard: the
"Digital Ultra Disc" or DUD. :) Once those violet lasers (or alternatives)
come down in price, there is little doubt that the World will be treated to
yet another advance in technology whether anyone wants it or not.
Here is my take. My track record isn't great on predicting the future as my
crystal ball has been broken for a long time, so don't buy or sell shares
in any company based on these comments!
DVD will do very well for data storage since due to its much higher capacity
compared to CDROMs (5 to 20 GB versus .64 GB), it will serve an important
purpose in the increasingly interactive applications and games to come.
Full size DVD will be overkill for many audio applications. At the normal CD
audio sampling rate of 44.1 K/second, the smaller DVD format will hold over 8
hours of music. Whether people will be willing to pay the expected price for
a DVD with several hours of music is questionable. There certainly will be
many good reasons to do this - full concerts or operas on a single disc, for
example. I would expect the average total length of normal musical DVDs to
increase beyond what is typical of CDs as well.
However, mini-DVDs are possible. A 3-1/2" format would hold about 1/3 as
much as a full size DVD or over 2 hours of music. This or an even smaller
format would be ideal for discman applications.
What about multilinqual sound tracks? Sure, this capability may save money
by requiring pressing of only one disc to support multiple markets. But,
few people will have a need to pay for this.
There are no doubt all sorts of applications that have not been identified
yet for which the DVD is ideal. However, the hopes of the industry are pegged
to DVD's success for video - in part, to replace the consumer (VHS) VCR.
Unfortunately, It is here where I believe DVD has its greatest weaknesses.
Many of the specifications have been developed tailored to today's video
standards, not HDTV. The DVD is supposed to be superior to both VHS VCR and
laserdisc formats. However, this is in comparison to standards (NTSC and PAL)
that are close to celebrating their 50th birthday. Even the quality advantages
are questionable as so much depends on the MPEG-2 encoding used to compress the
vast amount of video information onto the DVD.
Video tape and laserdiscs do not care what is recorded on them - they are
equally good or equally poor for static scenes as well as explosive action
shots. This is not true of DVDs. Complex images and rapid scene chances
require more bits to minimize artifacts. And, the types of artifacts that
are introduced are not those one expects from poor reception or bad tapes.
It will take a great deal of effort on the part of the companies who will
be converting original movies and other source material to the DVD to do
justice to the format. It may simply be impossible for certain action
sequences. The result may be 'pixelation' or momentary blockiness, erratic
motion, momentary freezes, and so forth - not just slight fuzziness or snow.
It is not known how the general viewer will accept these. Developers of source
material will not be free to put in whatever they desire. The medium may
break down when presented with too much fast complex action or rapid scene
changes.
The situation gets even murkier for HDTV where the required amounts of data
and data transfer rates increase dramatically. Depending on HDTV format,
this could be anywhere from 2:1 or 8:1 - or more. If the DVD is marginal now,
what does this say for HDTV?
Initially, DVD will not have record capability. Thus, there will be no
compelling reason to switch over and throw out your VCR especially if the
quality isn't dramatically better. The majority of consumers don't care
that much about picture quality anyhow. Beta, S-VHS, and laserdisc, all have
substantially better picture quality than normal VHS and NTSC broadcasts.
It has not mattered due to various usability issues and marketing stupidity.
The critical mass was never reached with respect to availability of source
or rental tapes or discs. Thus, these have been relegated to niche markets
and niche markets don't drive the industry.
Will DVDs turn into yet another Edsel, Selectavision, or Betamax? Only time
will tell but the industry must make a deliberate effort to assure the quality
of the initial releases or else DVD's future as a video media will be sealed
before it gets off the ground even if the technology there.
The earliest were called WORM (Write Once Read Many) drives. Writing
resulted in an irreversible change in an information layer. Thus, data could
be written but not erased and rewritten (though just erasing a block might be
possible). Heating with the writing laser beam resulted in damage (ablating)
of a coating. Reading is similar to that used for CDs and other optical
technologies.
Typical capacity was 650 MB per side. Disks could be one sided or two sided.
This is somewhat similar to the technology used in CD-R drives though many
variations have been developed which vary mostly in the details.
Unlike CDs, MDs, and LDs, these optical discs are formatted more like hard
drives or diskettes with circular (not spiral) tracks and fixed sectors - some
of which are visible to the naked eye since they are physically etched on the
disk itself.
The laser power for WORM drives is typically higher than for read-only drives
when in writing mode - likely in the 10s of mW range. 30 mW is one number I
have heard. Modern drives all use IR emitting laser diodes.
The basic mechanism and optical pickup is similar to that of a CD including the
techniques used for beam generation, focusing, and tracking. However:
The media is usually enclosed in a cartridge for protection with a door that
opens automatically when inserted into the drive. Capacity is typically
650 MB per side for a 5-1/4" disk.
Although CD-R started out being quite expensive (greater than $10,000 for a
recorder), it really was designed as an inexpensive technology and to have
total compatibility for reading with CDs and CDROMs. Current prices for
multispin (2X, 4X) CD-R recorders are under $500 and dropping. The capacity
of a CD-R is the same as a CD - about 650 MB.
Like the WORM drive, a higher power laser ablates a coating inside the CD-R
media. With most, this is a blue-green polymer dye backed by a gold coating.
Otherwise, construction of the CD and CD-R media are similar.
However, since the pits and lands are not as precisely formed as those of a
pressed CD whose master was made on a $250,000 laser cutting lath, some CD
players or CDROM drives may have tracking or other problems with CD-Rs.
CD-R recorders and high performance CDROM drives are very similar except:
Modern LD players use the same 780 nm laser diodes as CD players. Really
old players used Helium-Neon (HeNe) gas lasers resulting in a visible beam
at 632.8 nm (orange-red). CAUTION: these use a high voltage power supply.
Contact with this probably won't hurt you but will not be pleasant. The
high voltage terminals are probably well insulated but it is a good idea to
locate them and double check.
Since most LD players also play CDs (and possibly multiple size LDs as well),
there will be optical sensors - LED-photodiode pairs aimed at the disc from
one or more locations beneath the drawer assembly. If you have the top off
for servicing, room lighting may confuse these sensors resulting in all sorts
of strange behavior such as attempting to play a CD using the LD spindle!
Cover the entire unit with a piece of cardboard or just the holes in the
drawer with matt black paper to eliminate the possibility of both electronic
and human confusion!
LD players will generally have one additional servo system compared to CD
players - tilt. This adjusts the angle of the pickup with respect to the
disc to minimize interference between adjacent tracks. This would result in
degradation of the analog video signal. The tilt servo is usually pretty
simple using an IR LED emitter and a pair of IR photodiodes detecting the
reflection from the laserdisc. If after manually rotating the tilt motor
away from the balanced position, the tilt readjusts itself, there is a good
chance this it is operating correctly. There is probably a tilt balance
adjustment as well but don't touch it unless you have the service manual
if possible.
Spindle motors in LD players are of much higher quality than typical CD
players since the spindle must spin continuously at thousands of rpm with
the greater mass of the LD as well. Other motors may be similar to those
in CD players. Some LD players have two spindles that are selected and
moved into position depending on the type of disk being played.
Due to the mass of LDs, the clamper is even more critical to proper behavior
than for CDs. Any slippage and LDs may fail to be recognized.
There may still be rubber belts that degrade :-).
Naturally, a video monitor makes an excellent diagnostic tool once it is
possible to obtain some output from the LD player. A service manual is
almost a must for serious troubleshooting.
The following is a further confirmation that optical alignment should not be
needed under normal conditions:
(From: Dave A. Wreski (dawreski@nic.com).)
I have been servicing these since they came out. The *only* time I had
to do any optical alignments is when some fool decided to mess with the
alignments. They do not misalign themselves. In the past the only adjustment
we had to do (on Pioneer Laserdisc players) is the 1/4 wave plate which
can be done with a scope. All other alignments must be done with a Laser
power meter and a polarization adjustment jig from Pioneer. Many dollars!
If the optics are clean and haven't been maladjusted, your unit is suppose
to work. If not, look elsewhere in the electrical alignments or motor problems.
However, it should be possible to substitute a surplus HeNe tube and/or HeNe
laser power supply. The tube will have to be of a similar power output
(usually around .5 to 1 mW) and physical size. It probably also needs to
produce a polarized beam (which eliminates a lot of the common barcode scanner
tubes as replacements). If the beam diameter and divergence are similar, it
may be possible to get by without any optical alignment as long as the tube is
carefully mounted with its output in the same position and orientation as the
original. However, since these parameters are probably not known, there could
be problems with a swap. In that case, another tube can probably be made to
work but some amount of optical alignment (possibly just resetting the
position of one lens) will be needed. A service manual will be essential.
HeNe laser tubes with power supplies can be had for as little as $25 from
various mail order sources but you need to confirm compatibility. It may be
possible to compensate for a different beam diameter and/or divergence by
adjusting the external optics. However, you can't easily get a non-polarized
tube to produce a polarized beam. (It can be done with powerful magnets but
this is probably not a viable option inside a cramped LaserDisc player.) I
don't know if LaserDisc players do anything special with optical feedback or
anything like that but if it is just a power supply, this may be an easy and
inexpensive alternative.
If a suitable HeNe laser replacement is unavailable, too expensive, or just
too mundane, it may be possible to use a diode laser - even a laser pointer -
in its place. The beam characteristics would need to be similar with respect
to divergence and polarization. A unit with adjustable focus will probably
be best to match up divergence. Since, all diode lasers are polarized, that
at least, shouldn't be an issue. Apparently, some people have successfully
done such a transplant without major problems. The most difficulty may arise
from devising a suitable mounting arrangement and providing the stable low
voltage power needed for the diode laser or pointer. I'd still recommend
staying with an HeNe laser if possible but at least, there is an alternative
that will keep your prized 1979 LaserDisc player going strong. :)
(From: dwb@rell.com).
I had a problem with my Kenwood machine not locking the disc in place
correctly. The drive belt was slipping to bad (couldn't hear it though).
The replacement was a NEW mechanism that regeared the assembly for slower
feed but more more clamping force.
(From: Douglas W. Jefferys (dougj@freenet.hamilton.on.ca).)
How old is the player? I've worked on the Philips 22VP931 and seen similar
things. This is an ancient (ca. 1982) industrial player with a tendency for
the radial and tangential mirrors to jam in their servos. (The glue that
holds the magnets behind the mirrors weakens with age. If a magnet detaches,
the mirror jams solid, but the magnets can also migrate outwards and cause
sticky behavior).
If it's an older player, it's *possible* that it's in the early stages of the
same failure mode. (That said, all the 22VP931s I've seen that have this
failure have had *solid* jams on at least one of the mirrors, so I think it's
an all-or-nothing thing.)
Anyways, after fixing the servos (a nightmare - it's a good thing I had help
from a knowledgeable source about what to expect when I went into the guts of
the thing :-), I did an eyeball alignment (power *OFF*, machine unplugged, a
double-check that the power is off and the machine unplugged, and look down
through the objective and see if you can see down the entire beam path) and
got the same results you did. Worked fine on the early portion of the disk,
but slowly screws up later on. High-speed seeks worked marginally early on,
and not at all on later portions of the disk.
An examination of the player while playing showed that one of the mirrors was
near the limit of its range of movement at the point when the video started
freezing up.
NOTE: I'd strongly recommend *against* looking at the mirrors in operation
unless it's either a visible-beam system or you have goggles opaque to the
laser's frequency. I was willing to be somewhat stupid because it was a
visible-beam system, and I still used a piece of paper to ensure my head was
nowhere near the areas where bits of beam were leaking from the player. I
wouldn't have even fantasized about attempting this with an IR beam.
About three hours and umpteen incremental adjustments of the optical head's
alignment screws (which I had to remove and thereby misalign when fixing the
servos), and the thing was working fine.
Summary:
If you have contacts with professional fixers, I'd also suggest you bounce
your ideas off of them before proceeding. When hacking LD players, you're
always one mistake away from owning a very expensive pile of spare parts.
Here is a list of commands I have for controlling Pioneer players via the
RS-232C jack. Hope it helps. I have also heard that there is supposedly a MCI
driver for Windows but I haven't personally seen it. I tried these codes
on a Pioneer machine I have at work using the Windows terminal program and
was able to control the player. This file is from a public domain file for
the amiga. I think I also have a C program (also for the amiga) somewhere
if you need it.
Communication protocol:
I have just found a RS-232 test program for all Pioneer LaserDisc players on
Pioneer's web page. The URL is:
I tried it with my newly acquired LDV4200 and found that it did not work.
Right now I am fearing that my player has a problem with the control port.
The data seems to be coming through the cable as I get a flashing logic probe
when I hook it up but the player does not respond.
I'm not sure about the codes as they are not covered in the otherwise
excellent doc file (they always leave something out it seems).
However, I think you can get codes for your player through Pioneer.
The 8210 service manual is 120 pages long. This is not an easy unit to work
on. It is the very first industrial video disk player that Pioneer made. All
of the GM dealers had them when they first came out and I have seen them for
sale in most flee markets for around $50.00.
These are built like a tank and use a HeNe laser tube and a bunch of discrete
optics that are very hard to align properly without the manual.
(From: Steven B (lasers@netrus.net).)
The 90 series of laser player had a fault that was fixed by Pioneer at no
cost. It also caused a whole new series designation. Call Pioneer!
Your Pioneer LD has a shorted protective device, a V1B24 or similar. Looks
like a diode and is located near the main AC input to the board. Clip it
out, replace the fuse, and normal operation will resume. You STILL NEED to
replace it; it protects some very expensive chips. Get the reference
number off the board and call Pioneer at 800-457-2881.
I have seen that before. The Sled runs on a differential op-amp. This uses
+15V and -15V. One of these supplies is out. There are two fuses in power
supply for this. Most likely u blew one when changing spindle motor. This
will throw loading motor and sled motor, and maybe even the tilt motor (if it
isn't also the loading motor) into overdrive in 1 direction. Loss of either
supply will shift the differential one way.
Once the tray has finally opened, thereafter it behaves normally and responds
immediately for as long as the player is left on. Even if it's turned off
briefly and back on, the tray behaves OK. However, if I wait to the next day
the tray goes back to its nearly 6 second wait again.
There appear to be several opinions as to the cause
First suggests it is a sticky rubber problem:
(From: Jeff Boettler (boettler@us.ibm.com).)
Eject the LD drawer and disconnect from the mains. Then remove the cover. On
the 2950 there is a mechanism that clamps the disc that is suspended by metal
bars running over the top of the drawer. Remove this, around four screws and
locate the motor. There will be a rubber mat that grabs the disc. Clean this
with meths and nothing else. Allow to dry and reassemble.
Apparently this problem is accelerated by dirty labels on the LD and BBFC
logos that have been removed, which leave a nasty deposit that rubs off on the
mat.
(From: Bruce Esquibel (bje@ripco.com).)
I somewhat have a clue - but haven't came up with a 100% fix yet.
The trouble appears to be the upper 'track' that hub/laser assembly uses
when it returns from the side 2 position.
This track floats within the metal sleeve on the upper left hand side as you
look at the player from the rear (front away from you). It appears the last
inch or so is warped or slightly deformed, probably because of age.
If you examine the construction the track is pulled upward via a pair of
springs and held in by a couple L-tabs or ears from the track. When the
laser is returning from side 2 to stop you can see the track slightly move
as the motor on the hub assembly runs on it.
When it just about hits the end, that is when the grinding noise is heard,
the gear on the shaft of the motor is spinning, but not meshing with that
part of the track. It appears that after so much time the player detects the
error and starts 'slapping' the hub around and eventually it grabs and does
its flip.
Odd part about this is that even the slightest pressure on either the track
or hub will allow it to cycle without missing a beat.
What I did, which reduced the grinding, but did not fix the trouble
completely was to modify the rear spring to be tighter by carefully cutting
the loop off and unwinding one turn, making into another loop. I suppose you
can find another similar spring which has less turns also. The other bit
that helped was kind of cheesy, the rear L-tab from the track seemed to have
too much play when the motor ran near it. All I did was stick a small piece
of electrical tape under it, on the metal housing which also tightened the
track.
I'm pretty sure the track itself is the problem, but it looks like a
son-of-a-bitch to replace, even if it is a replaceable part. Another
possibility is the gear on the motor shaft getting worn down but being the
problem is only at that one end, I really don't think so.
If you aren't into repair (just a joe consumer), I really don't recommend
trying either the spring mod or tape bit, the spring can be easily malformed
or the L-tab can break off, which either happening will put you in a world
of hurt.
All I can add is don't bother greasing the track, was the first thing I
tried and it didn't help a bit. Also there was no indication of it needing
lubrication anyway. This is a tolerance issue between the gear and track.
The grinding noise, although sounding nasty, isn't really. It's not chewing
up anything and I didn't even notice nylon dust around the area where the
teeth are grinding. It's more of an annoyance problem than a major
malfunction.
I once fixed a 3090
that had a problem when stopping the LD and the pickup tried to turn
back over to side A. It actually made a grinding sound for awhile then
finally grabbed into the turning assembly and turned over.
The fix was to lubricate the metal guide shaft where it transfers from
the playing shaft to the shaft on the turn mechanism. After this was
done it has worked flawlessly.
(From: Ruben Panossian (malcor@ozemail.com.au).)
The Extended Function dip switches are for just that, extended functions,
which change certain characteristics of the player's operation. There are only
three extended functions, using switches 1, 2, and 4 only. The other DIP
switches are not used. Factory default is for all of the DIP switches to be
set in the "off" position.
The baud rate setting would not matter if you have nothing connected to the
interface. BTW, it should be set for 9600 for ALG games.
The objective is unable to find focus when this occurs. (usually) The disc
will not spin-up to speed, rather, a slower turn and often in reverse. To
determine if the player is finding focus you will need to get access to the
lower PCB's. Turn the player on its *side* and remove the bottom cover. (Do
*not* try to eject the disc in this position!) This is the servicing position.
The large board you will see, behind the lower cover, is called MB-40. You
will need to pull this board out a bit so you can work on it. Locate IC313,
it is an HA11529. This IC controls the focus (coils), tracking (coils) and
communicates to the main system control.
Looking at the schematics, you can see that pin 36 of IC313 drives the focus
coils. Pin 26 of IC313 is an output to the system control, which signals when
focus is locked. By using a CRO, connect one channel to pin 26 and the other
to pin 36. Adjust the display so that you can see the two signal but not on
top of each other. You will need a CRO (or DSO, whatever) as the signals are
about 3Vpp.
Turn on the LD player (with a disc already loaded) and watch the signals.
(the disc should be moving and sounds from the player) You should get a
ramping (triangular) signal on pin 36 for a moment then a steady line (0V),
indicating that focus has occurred. The signal on pin 26 (focus lock) is high,
when focus is not locked, and low when locked. When the focus is locked the
player should spin-up and go in to playback mode.
Now, if you are finding that focus locks then searches then locks, in a
peculiar way then you will have to do some more checking to determine the
problem. This can be caused by many things.
If focus is not locking and the signal on pin 36 is a constant triangular wave
then the problem is more than likely in the optical block or the laser not
turning on.
Check to see if the objective is free. Next, check the continuity of the
focus coils from the connector on the MB-40 board.
You can check if the laser diode is turning on by checking the test point
TP302 on the MB-40 board. It is located near IC312 which is a three pin -5V
voltage regulator. When there is -5V on this test point the laser should be
on. If there is no -5V there then check for -8 to -10V on R334 (any side) If
there is no voltage there then there is a voltage rail supply problem. (like
you hadn't guessed)
If there is around -10V, then check the base on Q314. This is the right pin if
the flat side is facing you, the right way around. It should have 0V on it to
turn the laser on. Hmm... I will try again. One pin is connected to the +5V
rail (collector), another pin, the emitter, drives the base of Q313 (which
then supplies -10V to IC312) which should have +5V on it when the remaining
pin (base) is at 0V. The base is connected to the LD "ON" or LD "OFF"
signal. It is an active low signal, so a low signal will turn "on" transistor
Q314 and in turn eventually turn on the laser diode. The laser diode also has
an APC which complicates things, but don't worry about that at the moment.
If the of base of Q314 is 0V and the collector is +5V then the emitter should
have almost +5V on it. If not then the transistor must be real hot or dead. If
it is hot, Q313 would be faulty. BTW, this transistor, Q314, is a pre-biased
"digital" transistor. It is either fully on or off.
I had a laser power problem like this, on a player out of a TT, which I had
previously repaired. This time it turned out that the laser was not turning on
all the time. Some times it would be ok for a couple of hours then it wouldn't
work properly. By the time I had taken the covers off it was OK again. (Grrrr)
To make a long and frustrating story short, I found that the laser wasn't
being turned on when it should all the time. Turned out to be a bad connection
on IC902, which is a 80 pin quad flat pack (SMD) and *only* pin 31 had a poor
connection. This pin controls the laser diode "on" and "off" signal. I think I
may have caused this poor connection when I was poking around previously.
Also be careful when probing around a SMD like IC902. If you inadvertently
short out a couple of pins, the slide motor may move (turbo) the optical block
towards the spindle and not stop, causing a nice gear jumping noise that
brings on a sudden panic attack. Which may cause you to knock over your LD
player while trying to find the "OFF" button while still holding a cro probe.
Although, I wouldn't admit to doing such a stupid thing, especially publicly.
:-)
Now, back to IC 313 on the M-40 PCB.
If you are not getting a triangular wave or steady line on pin 36, but a wavy
(sinus) signal then check the soldered joints on pins 38, 41 on IC313 and on
R384, R382, R381, C337, C338. These are for phase compensation for the focus
coil. If the signal looks strange on pin 36 of IC313 or the laser is turned on
and IC313 is not working then IC313 or the serial control input signals may be
your problem. I have only seen a couple of poor soldered connections on these,
otherwise A+, players but you never know...
If you find that focus is locking in say 10ms intervals (on and off) then the
problem may be in the focus loop, which is initiated right when focus is
locked. This loop controls the current supplied to the focus coil to maintain
a constant current which is proportional to the focus error, so the focal
point is maintained as the disc turns. Keep in mind that the focal length is
not constant, as the disc is rotating.
Or the problem could get interesting. In other words, *could* end-up being a
"dog" of a problem, unless you have a manual. Either way a manual is
essential. If you can read and understand the circuit diagrams then you
shouldn't have any problems, other than the faults that were devised in hell.
The frames played are identical for any given disc. Mad Dog McRee gave
me 7000ish, and Star Rider gave me 6900ish.
When the player is in this mode, pressing the eject button causes the
video to mute and the player to spin down. When the disc has stopped
rotating, a further press of the eject button will eject the disc
correctly, and a further pressing will reload the player."
Yes, this is normal. Even if the focus error is greater than it's cut-off
point the player will spin-up and try to display video. How good the video is
will depend on how great the focus error is, I guess. I have done this
myself, however, have found the video to be very jumpy and poor if any at
all. When the focus error gets to it's cut-off point it re-initiates focus
search..
If the video is clear and stable then your problem sounds like it is not with
the optical block, focus, etc. (with the test jumper closed)
The test jumper you found is *only* meant for adjusting the "inner" and
"outer" frame limits for the disc sizes, hence the displayed frame numbers.
1. The player works but is still configured for a video game; it has to have
something useful coming in on the RS-232 port in order for it to work."
No. There were different LDP1450 software revisions though.
With the Extended Function Dip switches all set to the "off" position the
player will "spin-up" a disc and go to playback mode, when a disc is loaded.
Yes and no. This is not your problem, though,.
Possible and no.
1. Am I doing something boneheaded?
No, considering the lack of information you have for this player. You could
have done worse...by poking around IC902. I don't think that you will get
very far without a service manual. The Sony service manual is relatively
expensive, however, it is essential, It is also well detailed and clear,
unlike some early player manuals.
Yes, from Sony :-). Because it is not a real old LD player, they will have
the manual.
This wouldn't help you with repairing the player, rather the opposite.
Also, I forgot to mention one of the first things you should check for. Check
the power supply voltages. Obviously +5V is ok. You should have an idea of
which voltages are ok by what is working in the player as a start,
anyway. There are around 10 voltage supplies or more including at least 5
different voltage rails.
Disclaimer:
If anyone goes blind, destroys their LD player, decapitates their dog Fluffy,
etc, by following my suggestions , it is not my fault. Only work on a LD
player if you have an idea of what you are doing and understand what the
dangers are. i.e., take blame for your own actions.
Unfortunately, for a typical LD player, this is just the beginning.
(From: Jack (jackh35785@aol.com).)
Replacing a spindle motor is a "can of worms". I used to build these things!!
You have a VERY critical height that is adjustable by three pylons with
screws, etc. You need a special disc which had a "constant pitch" from inside
to outside. There is also a method of doing this using a mirror disc (as the
CD folks know about). You absolutely must have the LD player service manual!
To write a MD, a magnetic head is brought in contact with the top of the
disk with the writing laser below. Without the magnetic head in place, no
recording takes place. I have seen a few of these (mostly SHARP) where the
actuator motor binds up. Taking it apart and freeing it up usually fixes
the problem.
For playback of prerecorded discs, the optics and servo systems are operating
in modes which are very similar to those in CD players and thus suffer from
most of the afflictions and remedies described elsewhere in this document.
The digital decoding and error correction including an advanced form of the
CIRC may be substantially more sophisticated for MD players and MD data drives
(if you can imagine that being possible) but the circuitry involved should be
very reliable.
However, for playback of MiniDisks recorded on MO (magneto-optical) media,
there can be many other problems as the optics/electronics are sensing the
different polarization of reflected light from the N and S magnetized spots
rather than pits and lands. The signal-to-noise ratio of the MO effect may
be lower than that of a stamped disc. Thus, prerecorded media with the normal
pits and lands on the information layer may work fine but MO media may suffer
from tracking, audio noise, or uncorrectable data errors. Servo adjustments
for tracking and CLV spindle control may be even more critical than for CD
players.
Note that some MDs may include both prerecorded (stamped) and MO sections
so that it is possible that only certain portions of these disks will play
reliably.
MiniDisk recording requires that the laser diode be operated at higher power
(around 4.5 mW optical output compared with less than 1 mW for reading) and
that an electromagnetic head in contact with the back of the MD is driven with
the EFM coded data pattern. This is not really a write head such as that used
in a computer disk drive - the laser beam does the actual writing by heating
the MO layer but the magnetic field determines the polarity (e.g., 1 or 0, N
or S) of the written spots. Therefore, the actual position of the head is not
critical - there is no servo for it! Note that this approach contrasts with
that used in many other MO drives where the laser power is modulated to write
1s and 0s. The 'Magnetic Field Modulation' approach used with the MiniDisk
claims many advantages in terms of robustness when confronted with less than
perfect optical alignment and control of laser power, among others.
CLV servo lock during recording is determined by a signal derived be impressing
a reference modulation (wiggle) on the premastered groove wall position - yet
another possible area for failure or need for servo adjustments!
CAUTION: the higher power laser output required for recording is substantially
more hazardous than that of CD players. However, since under normal conditions
even with the case disassembled, the disk and electromagnet will be blocking
the lens, there is little danger. However, if you remove the electromagnet
and there is no disk in place, this optical power must be treated with respect.
(From: Shawn (slin01@mail.orion.org).)
These is a very common problem with Sony MD/CD players. I'll bet it is
skipping and/or ruining your recordable MD's, right? It causes far more
"disasters" with MD because an MD deck that has trouble reading a recordable
MD will think it is corrupt and try to write a new TOC, which can ruin the
contents of the disc! When this occurs, press the STOP button until the "TOC"
indicator disappears (may take up to 10 seconds) and eject your disc, it will
come out unharmed.
Anyhow, on to the optical block problems. I will bet your MDS302 will work
fine if turned on its side or upside-down. I have seen this problem many
times with Sony MD/CD equipment. I have MD players from Sharp which are much
older and have suffered great abuses (like being run over by a car) which
don't suffer this problem.
My only guess is that it's either a problem with the lens suspension or the
focusing coil. It is definitely a problem with the focusing system in the
optical block because: A) replacing the block fixes the problem B) sometimes
adjusting Focus Bias on the deck will compensate and reduce or eliminate the
problem. C) I have fooled around under the cover of the optical block and have
experimented using pieces of tape to suspend the lens suspension. I suspect
this compensates for either a poorly functioning suspension or a screwy focus
coil. I have been able to regain 100% perfect operation using this fudge-fix
method!
Unfortunately, to fix this problem properly, you will need the new optical
block. We can only hope that Sony will correct this problem! BTW, you could
always use your deck upside-down or sideways. :(
While much of the basic construction of CD and DVD players is similar,
in order for a single player to work with both CDs and DVDs requires some
fancy footwork to avoid the costs of dual laser pickups. This comes about
from the change in the laser wavelength (780 nm for CDs, 632 nm for DVDs)
and thickness of the disc (1.2 mm for CDs, .6 mm for DVDs). This requires
differences in the optics to produce the proper spot size and readback
image on the photodiode array.
(From: Bill Studenmund (wrstuden@macro.stanford.edu).)
I saw an overview in a journal on what they're doing, and it's
pretty cool. They have a variable aperture in the beam (maybe it's on
a hinge and snaps into the beam path?). In one setting, the beam is the
right diameter to fill an inner area of the objective, and focuses
to a spot the right diameter for reading normal CD's. The spot has
correction for the spherical aberration from 1.2 mm of disk.
When the aperture is not in the beam, it fills the full aperture of the
lens. There's a holographic grating on the lens so the the combination of
the inner and outer areas is diffraction limited for 635 and compensates
for 0.6 mm of disk.
Though the signal to noise ratio will be lower as the 1/4 wavelength's a bit
off, I doubt it'll be a problem. The electronics have gotten so good that
they can read a disk w/o metal backing! That's how the Sony dual-layer disk
technique works. There are two surfaces with data, and the one in the disk has
no aluminum backing. They get enough S/N to read that layer. It's about 50 um
above the "normal" layer, so not much of a defocus.
As a practical matter, it is very unlikely that any existing CD player could
be made to work with such a scheme. It would be like viewing the pits through
a frosted plastic screen - theoretically possible but substantially reducing
the signal to noise ratio. Furthermore, the CD focus servo would very likely
lock onto the DVD rather than the CD layer as it goes through its focus search
routine.
It might be possible to design such a CD player but why would anyone want
one? By the time this matters, DVD players will either be mainstream (CD-only
players may not even be available any more) or will have been superseded by
something even more wonderful. Why would you pay a premium for a DVD pressing
and then only want to play portions of it on a CD player anyhow?
Well, I bought a few of those WORM drives I wrote about. The LD puts out
at 30mW at 110mA, As measured by using it to heat up a surface mount
transistor hooked up as a thermometer with a surface mount resistor glued
onto it for calibration.. I wish I had gotten more. Not that I know what I
will do with them (the LDs) The drives also have several rare earth
magnets so they were quite a fun deal.
I have a flyer on Mitsui CD-R media. I quote from this:
The difference between a CD-R and a CD-ROM lies in the structural layers
between the polycarbonate substrate and the protective lacquer surface that
both discs possess.
The CD-R has one long groove stamped in the polycarbonate substrate to guide
the laser. This groove is covered with an organic dye lyer, which, when written
upon by the heat of a higher powered laser light from the recorder, will deform
to produce the 'pits' and 'lands' of information. The dye is protected by a
non-corrosive, highly reflective thin layer of gold. One the CD-R layer is
recorded, the deformations in the dye become permanent.
The Mitsui gold CD uses a patented Phthalocyanine Dye & Data shield surface.
They then go on to mention how unlike Cyanine based CD-R, theirs shows less
degeneration from continuous exposure to light and heat.
Here is the fix I applied to my two year old HP 4020i CD-R recorder when I
started to get Write Append errors when writing CD's larger than about 550
MBs.
I got a tip that this problem was due to a "spring" wearing out or of
insufficient strength from David Neal on the cdwrite@pixar.com mailing list
(Unix CD-R software mailing list).
Armed with this clue, I searched DejaNews on the subject of CDD2000 & Spring.
Here I found basically two theories for the problem - the spring theory and
another one that said it is dust on the laser lens that needs to be blown off
with compressed air (*not* wiped).
Since my HP 4020i drive is over two years old, I figured I had nothing to lose
by opening it up and seeing if I couldn't apply the "spring fix". Also, at
the same time I blew off the laser lens with compressed air.
After applying the "spring fix" and blowing the lens with air, the drive now
works 100% again. I cannot say with confidence which of the these actually
fixed the drive.
I attach the approximate procedure I used for applying the "spring fix" below.
I disclaim any responsibility for the correctness or incorrectness of this
fix. Apply the fix will void your warranty. You should not attempt the fix
unless you have the proper tools and ability.
Tools Needed:
The next step is to remove the main circuit board by disconnecting three
ribbon cables and two sets of two pin connectors. The larger ribbon cables
are released by moving two pieces of plastic at each end of the cable
connector away from the connector body by about 1/8". The cables should then
easily slide out of the connector. The smaller cable has a slightly different
release mechanism, but again just move it about 1/8" away from the connector
body. Slowly rock the two pin cables from their sockets.
You should now be able to see 4 more T-10 screws. Remove these to free the
drive mechanism from the other part of the metal case.
The next step is to remove the smaller circuit board on the laser transport
assembly. Remove 4 philips head screws. Pull the board up and lay it over -
you will not be able to fully remove the board because two wires are soldered
to the motor.
If you look at the transport now, you will see a worm gear which drives a
regular gear which drives a rack gear. The rack gear is spring loaded to
press up against the regular gear. According to theory, the spring which
causes this pressure is worn out and/or not designed to be strong enough.
The spring itself is a straight length of springy wire, about 1" in length and
rumored to be about .012" in diameter. Since I don't own calipers, I couldn't
verify this.
The spring is held in place only by its springiness. Each end fits into a
slot and the middle is bowed down an under a notch in the plastic rack gear.
What you want to do is add a *second* spring wire. You should not need to
remove the original spring wire. I found a suitable wire in a 5.25" floppy
drive I had laying around. I removed the wire from the floppy drive and
straightened out a couple of bends that were in it and ended up with a
straight piece of springy wire about 1.25" long, which is longer than the
spring in the CD-R drive. You want it longer for now because it is easier to
install it that way. It will be cut to length later. Use the two pairs of
needle nose pliers to straighten the spring wire.
With your finger, rotate the worm gear on the shaft of the motor to move the
transport carriage so that the center of the spring is under the center of the
regular gear. You should be able to see the notches that hold both end of the
spring now.
Lay your new spring on top of these notches. Using the blade of a small
screwdriver perpendicular to the length of the spring, press the spring down
in the middle until it is underneath the slot in the black rack gear. This
bows the spring about 1/8" in the middle. The spring should now be in place.
Using your smallest dikes, cut the ends of the spring wire off so that they
are the proper length. Wear eye protection when doing this, and if possible
grasp the end being cut off with needle nose pliers so that the wire won't fly
around the room or worse into the drive mechanism.
With the drive still opened up, use a can of compressed air to blow off the
dust on the laser lens. DO NOT touch the laser lens as it is magnetically
floating in its holder.
Now, reassemble the drive by reversing the disassembly instructions.
-- end V1.30 --
All Rights Reserved
2. There is no charge except to cover the costs of copying.
DISCLAIMER
Working on optical storage equipment entails a number of personal risks:
electrical, laser, mechanical, as well as the possibility of irreversible
damage to the equipment and loss or corruption of data due to improper
repair or adjustment.
Introduction
Scope of this document
While compact disc (CD) players and CDROM drives account for the vast majority
of optical disc platforms in the known universe, there are other types in use
for both entertainment and data storage applications. These include:
SAFETY
In addition to the usual safety precautions outlined in the document: "Safety
Guidelines for High Voltage and/or Line Powered Equipment", some of this
equipment has the added risk of vision damage from the higher power lasers
that may be used for disk writers or recorders.
For more information on CD and optical disc technology
Philips/Magnavox used to have a very nice on-line introduction to a variety
of consumer electronics technologies. Although their site has disappeared -
and even people who work for them have no clue - I have now recovered
several of the articles including those on TVs, VCRs, camcorders, satellite
reception, and connections. See the Introductory Consumer Electronics
Technology Series.
Technology Specific Principles of Operation
LaserDisc (LD) Players
This is actually the oldest of the optical disc technologies to be introduced
to the consumer market. In fact, most of its applications are for analog
video storage - feature length movies and interactive learning tools and
video games.
(From: Mark Zenier (mzenier@netcom.com).)
So what about the RCA "CED" video player?
CED stood for something like "Capacitive Electronic Disc" probably with a
"Selectavision" label.
MiniDisc (MD) recorders/players
The MiniDisc cartridge looks somewhat like a small (2-1/2") version of a
3-1/2" computer diskette. Both players (around) $400 and player/recorders
(around $700) have been introduced with disappointing sales. Not enough
prerecorded material was available and the prices were too high to lure
people away from the convenience, low cost, and limitless variety of the
audio cassette medium.
Digital Versatile (or Video) Disc (DVD)
The DVD is destined to replace the CD as *the* optical medium of choice in
the near future. This will happen if for no other reason than manufacturers
will stop producing CD players (since DVD players will be able to read CDs).
The 8-fold increase in storage capacity per layer is accomplished through a
number of incremental enhancements to the basic CD technology including:
This permits:
For readout on both sides of a dual-sided DVD, dual optical pickups can be
used where the user is willing to pay for this significant added expense!
Are blue lasers used in DVDs?
The readout laser for DVDs is red, around 650 nm. This is similar in color
to a typical red LED.
Will DVD be the killer format?
There has been and will continue to be a lot of hype with respect to the
incredible advantages of the Digital Video (Versatile) Disc for everything
from computer multimedia to HDTV.
DVD FAQ?
Well one, at least:
WORM drives
A large number of technologies have been introduced to provide storage of
large amounts of information on optical platters with varying degrees of
flexibility.
Magneto-optical drives
Most modern optical drives use magneto-optical techniques in some ways similar
to the MiniDisc. However, unlike the MD, the laser beam is switched at high
speed to alter the magnetic properties of the coating and a write cycle is
usually a two step process:
The laser power for MO drives is typically higher than for read-only drives
and likely in the 10s of mW range. Modern drives all use IR emitting laser
diodes.
CD-R Recorders/Players
These use media that is the same size as the CD but can be written once and
is then read-only like the WORM disk. In many ways, this technology is similar
to WORM except that the format is a spiral track like that of a CD rather
than circular tracks and sectors like other optical disk formats or hard
and diskette drives.
LaserDisc Players
Considerations when troubleshooting LaserDisc (LD) players
CD and LD players share much of the same optical technology. Many models
will play normal audio CDs as well as LDs. If this is the case, start by
determining if a CD will play properly. If it does, then you can be fairly
sure that most of the optics and front-end electronics are functional.
LaserDisc optical alignment?
As noted elsewhere, optics don't generally drift except from abuse.
Replacement for Helium-Neon laser tube and power supply components
Older LaserDisc equipment used a Helium-Neon (HeNe) laser instead of a laser
diode. These use a HeNe laser tube and require a high voltage power supply
for operation. The tube can wear out or get broken and the power supply can
fail. Obtaining an exact replacement of either is probably virtually
impossible today and too costly in any case.
Kenwood LaserDisc clamping problems
With the larger mass of a LaserDisc compared to a CD, clamping is even more
critical. Slipping belts are a common cause of clamping problems.
Philips Laser disk problems and discussion
"A friend of mine has a Phillips Laserdisc player that is acting up. What it
does is the player will just stop playing in the middle of the movie, usually
in the same spot."
One final note: Some of the alignment things can be "one-way" adjustments, and
anything on the optical path is vulnerable to scratches. I'd strongly advise
trying to find the service manual before attempting any modifications.
Pioneer Laserdisc RS-232 commands
(From: Jim Jackson (jim@aviendha.demon.co.uk).)
COMMANDS CHARS HEX DECIMAL COMMENT
----------------------------------------------------------------------------
Door Open OP open the door
Reject RJ stop disc rotation
Start SA start disc rotation
Play PL (address)PL
Pause PA
Still ST still frame
Step Forward SF
Step Reverse SR
Scan Forward NF
Scan Reverse NR
MultiSpeed FWD MF (address)MF
MultiSpeed REV MR (address)MR
Speed SP integer SP
Search SE address SE
Stop Marker SM address SM
Frame FR set frame mode
Time TM set time code mode
Chapter CH set chapter mode
Audio Control AD integer AD
0=off,1=Ch1,2=Ch2,3=stereo
Video Control VD integer VD 0=off,1=on
Display Control DS integer DS 0=off,1=on
Clear CL clear entry or mode
Frame # ?F get frame number
Time code # ?T get time code number
Chapter # ?C get chapter number
Player active? ?P P00=door
open,P01=park,P05=still
Disc status ?D 5 bytes and CR returned
(and a few others....)
SERIAL PORT CONNECTION:
Computer Player
---------- --------
TxD 2 3 RxD
RxD 3 2 TxD
CTS 5 4 DTR
GND 7 1 GND
For more info on your type of Pioneer player:
Pioneer Communications of America, Inc.
Engineering and Technical Support Deptment
Sherbrooke Office Center
600 East Crescent Avenue
Upper Saddle River, NJ 07458-1827
Pioneer LaserDisc player test program
From: Colin Kraft (ckraft@airmail.net).)
Comments on Pioneer 8210
(Portions from: Dave A. Wreski (dawreski@nic.com).)
Pioneer '90' series LaserDisc player doesn't play older LDs
"Check those discs you are playing. My 1090 won't play some older Image
Discs including my (BOO HOO!) Bride Of Re-Animator disc."
Pioneer CD/LD Player Model CLD-S104 with shorted power supply
(From Mark Z. (zmachar780@aol.com).)
Pioneer 503 LD player sled slews to one end after service
(From: illusion@pqc.com).
Pioneer CLD-D701 tray locking problem?
"I've owned a Pioneer 701 laserdisc player for many years. Other than its
tendency to drift out of alignment slowly and steadily over the years, it has
been a good LD player. However, within the last year the tray has developed a
strange problem. Each time I turn the 701 on and press the eject button to
load a LD it takes about 6 seconds of gear grinding before the tray finally
decides to come out. Just a couple of years ago the response was almost
immediate.
Pioneer LD-3090 turn over problem
(From: Kurtis Bahr (kbahr@erols.com).)
Sony LDP-1450 problems and discussion
"I'm the proud owner of a very confused LDP-1450 from a Mad Dog McRee machine.
It's got six option DIP switches, all are "off" (down), and>it's set for 1200
baud."
"Power-Up: Disc rotates 10-30 degrees in random directions, changing
directions erratically every half-second or so, and the head makes a weird
squeaking sound periodically as it tries to seek (maybe it's making physical
contact with the disc??)"
"Self Test: Removing the front cover revealed a "self test" jumper. Shorting
the two pins together forced the player to spin up. The player correctly
displays video for a few seconds (overlaid on the video is a frame number
of approximately 7000), but quality, which starts off great, deteriorates
rapidly, and the player then jumps back 100 frames or so and repeats the
cycle. The words "NTSC 12" appear underneath the frame number whenever the
self test jumper is shorted.
"Theories:
"2. This might be changeable (or I might get a different set of diagnostic
information) if I knew what to do with the six option DIP switches."
"3. The player is malfunctioning, probably something to do with alignment of
the slide on which the optical head moves, and this accounts for the weird
looping behavior I get in the self-test mode."
"Questions:
"2. Anyone know where I can get a service manual?"
"3. I have yet to hook it up to a computer. I have a utility that purports
to be able to talk to an LD player; would this help, or should I concentrate
on getting it to work correctly in stand-alone mode before trying to talk
to it?"
Replacing a laserdisc player spindle motor
With a CD player, all you have to get correct is the spindle height.
MinDisc Equipment
MiniDisc record/write problems
(From: David Vlack (cptvdeo@ainil.com).)
Sony MiniDisk player/recorder considerations
The Sony MiniDisk system was supposed to replace cassette tape as the preferred
medium for portable music (and data). Yeh, well, I am not holding my breath
but it may yet come to pass. The disks are about 2-1/2 inches in diameter and
enclosed in a protective case like a 1.44 MB diskette. Thus, dirty disks, at
least, should not be much of a problem. A MiniDisk (MD) holds approximately
1/5th as much raw data as a full size CD. Compression techniques are used to
achieve the same maximum time for audio - about 74 minutes - supposedly with
negligible loss in audio quality. (I won't get into that argument either).
Sony MDS 302 Minidisc optical blocks
This likely pertains to other Sony models as well.
DVD Equipment
CD and DVD support on same drive
Digital Versatile (or Video) Disc players should be hitting the streets
by now or at least very soon. What this means is that DVD players will
need repair just like CD players.
Could DVD discs be made with compatible CD tracks?
CDs are 1.2 mm thick. DVDs consist of two bonded .6 mm substrates. In
principle, the DVD layer could be made partially transparent permitting a
CD player's laser beam to focus through it to some tracks of CD information
pressed in their normal position 1.2 mm from the bottom surface.
WORM Drives
WORM drive Laser Diodes
(From: Alan Shinn (alshinn@sirius.com).)
CD-R Equipment
Differences between CD and CD-R media
(From: Michael Portmann (mikep@adelaide.on.net).)
HP 4020i/Philips CDD2000 Spring Fix for Write Append Errors
(From: Rick Richardson (rick@dgii.com).)
Parts Needed:
Skills Needed:
The first step is to remove the case. Remove two screws with the T-10
screwdriver and four screws with the T-? screwdriver. Remove metal case.
Gently release the top circuit board from two plastic alignment posts -- this
may require gradual rocking of the circuit board but do not stress the circuit
board as it is very thin.
